1
Turbo Tuning / 173 Launch control
« on: September 13, 2013, 09:57:36 PM »
Is the 173 ECU going to have Launch control at any point? or is that not possible?
War Chip Forums
- April 18, 2024, 02:42:34 PM
- Welcome, Guest
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
Turbo Tuning / WOT Switch
« on: August 26, 2013, 06:33:31 AM »
Having a little trouble finding info on which wire to cut for the TPS, I know it's the Wire that sends WOT signal but not sure what pin that is. Any help would be appreciated!
89 325i turbo
Thanks
89 325i turbo
Thanks
3
Turbo Tuning / Re: Fuel Issues
« on: August 25, 2013, 07:49:50 PM »
Found the answer! the base map i was usuing was for some reason making the car run like crap but i wrote a new map and it fired right up! just getting the clutch broken in now then off to the tuner!
4
Turbo Tuning / Re: Fueling help!
« on: August 20, 2013, 09:34:52 PM »
No they are 42lb injectors, my mistake, I bought all the parts so long ago i forgot what i have lol, anyway i called miller earlier tonight and not sure if it was brody i talked to or not, but I also forgot to splice the wiring for the 12volt MAF so i did that and the car still is just running super rich, so rich its fouling the plugs out, I tested the MAF and the voltages tested out fine, Im stooped. Its acting like the MAF is not even there. Also i noticed i had my rev limit set to 3800 just so i knew the computer was getting the tune and it reved right past that point, any idea why that would be? Im beginning to think this is a mechanical problem and not a tune/maf problem, i just want to drive it already. the build took long enough lol. hellllp
PS: I checked the timing 3 times and im fairly certain its not an issue.
PS: I checked the timing 3 times and im fairly certain its not an issue.
5
Turbo Tuning / Re: Fueling help!
« on: August 20, 2013, 07:49:39 AM »
Ah yes I forgot that, ya I'm a 173, but thanks for the info anyway
6
Turbo Tuning / Re: Fueling help!
« on: August 20, 2013, 06:34:45 AM »
Actually it's only 4 values lol I suppose you could just tell me those, that would be a lot easier, originally the cam was 180 out, it was firing on the exhaust stroke, so I pulled the belt and fixed that now I'm at least getting it to fire, it's a mess lol but I'm sure will figure it out
7
Turbo Tuning / Re: Fueling help!
« on: August 20, 2013, 05:39:54 AM »
Ya I'm fairly positive it's running on the chip, ill drop the rev limit to 3k when I get home to make sure, that's the only way to check right? Other then that I can't figure it out, could you screen shot your "cranking fuel map for me?
8
Turbo Tuning / Fueling help!
« on: August 19, 2013, 10:29:59 PM »
Hello, looking for some help here, its also a fuel issue,
setup is:
89 325i
Walbro 255 pump
stock FPR
42lb inj
draw through MAF
Tonight was the first night i tried to start the car after the turbo build and the car wont even consider starting unless the throttle is 100% open and when it does get started it is running so rich it wont idle, not sure what the cranking fuel map is suppose to look like but it just seem way loaded up when i do get it too fire, any help would be great! thanks guys
setup is:
89 325i
Walbro 255 pump
stock FPR
42lb inj
draw through MAF
Tonight was the first night i tried to start the car after the turbo build and the car wont even consider starting unless the throttle is 100% open and when it does get started it is running so rich it wont idle, not sure what the cranking fuel map is suppose to look like but it just seem way loaded up when i do get it too fire, any help would be great! thanks guys
9
General Discussion / Re: Hoemade 4in MAF housing
« on: August 19, 2013, 10:10:05 PM »
Ya thats what i was thinking, thanks for the heads up!
10
WAR Software Support / Re: WAR CHIP Upload stuck at 9%
« on: August 14, 2013, 08:26:37 AM »
Ya i figured that out lastnight, got it to upload 
i use macs so this whole PC thing is foreign to me lol
i use macs so this whole PC thing is foreign to me lol
11
WAR Software Support / Re: WAR CHIP Upload stuck at 9%
« on: August 12, 2013, 01:22:41 PM »
Hey, I downgraded the java and it's still stuck at 9%, any word on how long until the update?
12
General Discussion / Hoemade 4in MAF housing
« on: August 12, 2013, 12:34:17 PM »
My turbo has a 4in intake and i have a 4in intake air filter so i needed a 4in MAF housing so i made one!
13
Projects / My build tread "hoemade"
« on: August 12, 2013, 12:30:07 PM »
Check it out and let me know what you think!
http://www.r3vlimited.com/board/showthread.php?t=290952
http://www.r3vlimited.com/board/showthread.php?t=290952
14
Turbo Tuning / Re: WAR Chip load axis
« on: August 06, 2013, 10:18:14 PM »
Great post, thanks for sharing
15
Turbo Tuning / Re: Hello!
« on: August 06, 2013, 10:15:12 PM »Pretty excited about this, my build is just about done and I may need a little assistance, I have some tuning expirence but im sure there are things im not going to understand, 3076R 60#inj 12psi, Should be a good runner! anyway, this is great! and i look forward to getting to know the guys at miller.
Thanks! heres a link to my Build http://www.r3vlimited.com/board/showthread.php?t=290952
Sounds like a solid setup. Definitely post up if you have any issues, I'm sure one of us will be able to help
Pages: [1] 2